LED curing light Starlight PRO

Cordless curing light for curing composite filling materials
Power types
2 curing modes: "fast" mode (10 sec.) and  "slow rise“ mode (20 sec.)
Country of original
3 years
REF. №

The cordless LED curing light Starlight PRO fits perfectly into your dental office

A cordless LED curing lamp for flexible use that can be taken from one room to the other. Thanks to its high performance level and the long-lasting lithium-ion battery, it will run for 320 cycles of 10 seconds each in succession and recharging takes only 120 minutes. Its output can be checked thanks to the built-in radiometer. starlight pro can be relied on to harden a 2-mm thick layer in only 10 seconds and is extremely light (only 105 g). It provides a choice between two operating modes: “Fast-Curing” and “Slow Rise” (soft start).


Optical fiber

Sterilizable, coherent, fibre optics conductor, Ø 8 mm

Click-clack connection protection

Exclusive connection in metal ensures an optimal light beam transmission

Low temperature
It does not require a fan as it develops no heat – silent

Chargin station

  • green control LEDs indicating mains supply and signalling consent for charging process and power output
  • in case of problems a yellow LED will flash


  • integrated radiometer which checks the power output
  • result indicated by a LED

Processor control

Constant light power regardless the charge level

Low battery warning

The double acoustic signal is activated when the battery is still sufficient for 6 cycles

Charging time
Only 90 minutes


320 cycles with 10 seconds

The smooth, continuous and compact surface enables perfect disinfection

Light spectrum 

график диапазона длин волн полимеризационной лампы Starlight Pro

Starlight lamps are effective on camphoroquinone, used as photoinitiator in 98% of the materials on the market. They emit light on a wave-length comprised between 440 nm and 480 nm with a peak at 460 nm.

Operating mode

график режима работы полимеризационной лампы Starlight Pro

„Fast“ mode: 10 seconds at maximum light intensity, with acoustic signal at the beginning and at the end of the cycle.

„Slow rise“ mode: 20 seconds with a progressive increase of the light intensity reaching the peak within the first 3 seconds, one acoustic signal after 10 seconds and one at the end of the cycle.

    Device compliant to Dir. 93/42/CEE:Class I
    Classification as per EN 60601-1:

    Type B
    IP 20 (recharging unit)
    IP 22 (handpiece)

    Power supply voltage: recharging unit: 100-230 Vac 50/60 Hz 15 VA
    handpiece: lithium-ion battery, 3.7 V 1100 mAh
    Charging time:About 2 hours
    Device for intermittent operation: 120 sec ON 40 sec OFF Max 3 times running
    Light source:High-luminosity LED with optics  
    Class 2 M (IEC 60825-1) LEDs  
    Dominant wavelength: 440 - 465 nm  
    LED light emission: > 1.400 mW/cm2  
    Average life: 1,800,000 cycles, 20 seconds each
    Optical fiber:

    Diameter 8 mm
    Composition: Drawn coherent fibers surfused in transparent quartz  
    Autoclave sterilizable (max. temp. 135°C for 20 minutes - max. 500 cycles).

    Exposure:Fast: Exposure time 10 seconds - Acoustic signals indicating start and end of exposure  
    Slow rise: Exposure time 20 seconds - Acoustic signal at the start, after 10 seconds and at the end of the 20 seconds  
    The cycles can be stopped or repeated at any time
    Operating conditions:from +10°C to +35°C
    Relative humidity from 45% to 85%
    Pressure of air P: 800hPa/1060hPa
    Transport and storage conditions: from -20°C to +40°C
    Relative humidity from 45% to 85%
    Pressure of air P: 500hPa/1060hPa
    Weights and sizesRecharging unit: Weight 555 g 
    L - W - H 96 x 120 x 58 mm  
    Starlight pro handpiece: Weight 105 g 
     L 198 mm, max. Ø 23 mm
    Warrantydevice 3 years
    • Starlight PRO handpiece
    • Starlight PRO charger
    • Power Cord
    • 8 mm optical fiber, black with metal click-clack connection
    • Optical protection

    Do you want to buy this product?

    Leave your contact details, we will contact you by phone

    By pressing «Submit» button, you accept the terms of user agreement